3D
MAGISCAN
Back to all articles

How Much Does It Cost to 3D Scan an Object?

How Much Does It Cost to 3D Scan an Object?

A 3D scan can cost $0 on a phone, about $250 to $2,000+ per object at a service, or about $369 and up to buy a scanner. Here is what moves the price.

Scanning an object can cost nothing beyond your time on a phone with a free app tier, or roughly $250 to more than $2,000 per object at a professional service on Artec's 2021 figures. Buying a scanner runs from about $369 for an entry-level Revopoint model to tens of thousands of dollars for professional hardware, so your real figure depends on the accuracy you need and how often you scan.

The prices below were read from each seller's page on 2 November 2026 unless another date is given. They change, so treat them as a starting point.

What does each way of scanning cost?

Route Typical cost Fits when
Phone plus an app such as MagiScan or Polycam $0 on Polycam's Free plan; $150 a year or $30 a month on its Basic plan Looks and rough shape matter more than tight tolerances
Entry-level scanner Revopoint lists its RANGE 3 from $369, its INSPIRE 2 from $549 and its MIRACO Plus from $2,199 You scan often and will process the data yourself
Rented professional scanner About $250 to $475 a day (2021 figures) A short batch of parts, with someone who can run it
University or lab service €130 an hour plus VAT at Savonia in Finland A single part, if a lab near you takes outside work
Commercial scanning service $250 to $2,000+ per object (2021 figures) One-off parts where the result has to be dependable
Professional scanner US $9,900 to US $38,300 for Artec's Eva and Leo Regular scanning to a stated accuracy

What does a scanning service charge per object?

Artec's guide to scanning costs, dated 30 April 2021, gives a range from $250 for smaller parts to $2,000 or more for larger ones. Its US service team priced three examples: a car rim at $800 to $1,200 depending on the detail required, a black and shiny radiator grille at around $800 including spray preparation, and a dual-clutch transmission at $1,200. Artec also sells scanners and these figures date from 2021, so use them as a ballpark, not a quote.

Published hourly rates give you a second check. Savonia's price list charges €130 an hour plus VAT for scanning and €90 an hour plus VAT for post-processing. Travel is billed separately at €60 an hour plus VAT, plus mileage.

Savonia says an object about the size of a milk carton can be scanned and modeled in under an hour, with about half an hour more for measuring and reporting. An object the size of a small passenger car may take several days, plus another day for measurement and reporting. At the hourly rate, the milk carton comes to at most about €130 plus VAT before any measuring report. That is our arithmetic, not their quote, and a commercial provider elsewhere will charge differently.

Most of the time on a job is not the pass with the scanner. Artec's transmission took about 20 minutes to scan, about 50 minutes to reconstruct and 110 minutes to process. The hours go mainly into turning raw capture into a usable model, so what you want at the end can move the quote more than the scan itself.

What makes a quote go up or down?

Artec's guide and Savonia's page point to the same drivers:

  • Size. Savonia describes the scope and duration of a job as almost directly proportional to the size of the object.
  • Geometry. Holes, fine lines, sharp edges, overhangs and threads take longer. Artec notes that a small, complex part can cost more than a large, simple one.
  • Surface. Shiny or black parts may need a coat of scanning spray and a clean-up afterwards. A can runs $10 to $50, and applying it and masking off sections takes time on top. If you are trying this yourself, see how to 3D scan shiny, black or transparent objects.
  • Quantity. Each part is scanned and processed on its own, and a scan ready for reverse engineering often means taking the assembly apart first.
  • Accuracy. The tighter the requirement, the more capable the equipment has to be, and the more the work costs.
  • Color and texture. A model for a web store, a game or AR may need texture work from a 3D artist. A scan taken only for measurements does not need color at all.
  • Output. Artec says raw scan data usually comes at no additional cost, while a parametric CAD model costs extra, with reverse engineering starting at $100 to $200 an hour.
  • Location. A large or remote object can add travel time, extra people, a ladder or a crane.

Check the output line first. A quote for a mesh and a quote for an editable CAD model are quotes for two different jobs.

Can you really scan an object for free with a phone?

You can, within limits, and you pay in your own time instead of fees. MagiScan, an iPhone and Android app that turns a phone into a 3D scanner and measuring tool, exports scans for 3D printing, AR and e-commerce. Those are sensible first tests for a phone when nothing has to fit to a tolerance. App plans change, so read the current price on the store listing of whichever app you are considering.

Polycam's pricing page shows how a free tier can be limited. Its $0 Free plan lists limited object captures and GLTF exports, while Basic lists unlimited object captures and six mesh export formats. Check the export format before you count on a free tier, because a model you cannot get out in the format you need does not finish the job.

Take a seller who wants 40 products in a web store. At Artec's $250 low end that is $10,000 before any texture work, and a volume discount could lower it. A phone app on a plan priced like Polycam Basic at $150 a year costs far less in cash, and the real cost moves to your staff's time. Expect some re-scans and repairs, and budget time to fix holes and clean up each scan.

A phone stops being the cheap option when a part has to fit something else or be checked against a drawing, because a failed print or a wrong measurement costs more than the scan. Whether a phone app is enough comes down to the tolerance your job requires, and how to get accurate measurements from a 3D scan covers what you can do to tighten the result.

When does buying or renting a scanner pay off?

Entry-level hardware can cost less than one medium-sized service job at Artec's 2021 prices. Revopoint's store lists the RANGE 3 from $369 under a launch special, then the INSPIRE 2 from $549, the POP 3 Plus from $619, the MINI 2 from $829, the MIRACO from $1,499 and the MIRACO Plus from $2,199. Those are starting prices, and you take on the operator's work yourself. Artec's advice is to see results on at least one of your own objects before you buy, and that holds for any brand.

Artec's store shows what the professional end costs. The Eva is US $9,900 under a limited-time offer, the Point II US $25,600, the Spider II US $29,700 and the Leo US $38,300. The Micro II, a metrology-grade desktop unit with 5-micron accuracy, is US $24,240. The Ray II, a long-range laser scanner for massive objects, is US $97,800.

Ask what the bare scanner price includes. The Eva is US $20,320 as a Premium Pack, which Artec describes as scanner, advanced software, accessories and insurance in one package, and an Artec Studio Pro subscription is listed at US $1,700 a year.

Artec argues that at an average of $1,000 per scan, two or three parts a month pay off one of its scanners in a year. That is $24,000 to $36,000 a year in avoided fees, but it is a seller's sum and leaves out the operator's time. Artec also says that if you only need one scan, a service is much cheaper. To test your own case, divide the all-in scanner price by what a service quotes you per part. Then ask whether you will reach that count in a year and who will do the processing.

Renting sits in between. Artec's 2021 guide gave about $250 to $375 a day for an Eva or Space Spider and about $475 a day for a Leo, and it notes that rental prices differ between companies. At those rates, two to three days with an Eva costs about the same as one $800 service job. Renting suits a batch of parts or a trial before buying, not a single object.

How do you budget for one object?

  1. Decide what the model is for: looks, a print that must fit, measurements or editable CAD. That decides the route more than the object does.
  2. Write down the accuracy you need and what can be left out. Savonia lists this as the first step of its workflow, because it avoids unnecessary work.
  3. If the tolerance is loose, try a phone first. A failed test costs you little.
  4. If you need a quote, send overall dimensions, photos, the material and finish, the number of parts, the accuracy, the file format and your deadline.
  5. Ask what the price includes: preparation, post-processing, CAD and travel. Compare final deliverables, not hourly rates, because an hourly rate says little until you know the hours.

For most non-critical objects, start on a phone with an app like MagiScan and pay a service only when the result has to meet a stated tolerance. If the part has to fit or be inspected, budget the service figures above from the start.

Frequently Asked Questions

How much does it cost to 3D scan a small object?

Artec's 2021 guide starts service pricing at about $250 for smaller parts. At Savonia's published €130 an hour plus VAT, a milk-carton-sized object can take under an hour of scanning and modeling. On a phone, the cost is the app plan, which can be $0 on a free tier, plus your time.

Is it cheaper to buy a 3D scanner or pay a service?

For one object, a service is usually cheaper than professional hardware, and Artec says so itself. An entry-level scanner from $369 can cost less than one medium-sized service job, but you take on the scanning and processing. If you need parts scanned every month, owning a scanner starts to make sense.

Does a 3D scanning service charge extra for a CAD file?

Usually, yes. Artec says raw scan data generally comes at no additional cost, while a parametric CAD model costs extra, with reverse engineering starting at $100 to $200 an hour. Ask for mesh and CAD prices separately.

How much does it cost to rent a 3D scanner?

Artec's guide, dated 30 April 2021, gave about $250 to $375 a day for an Eva or Space Spider and about $475 a day for a Leo. Rental prices differ between companies, so ask for a current figure and check whether software is included.

Back to all articles